產品展示

當前位置:主頁 > 產品展示 > TT電子(TT Electronics) > 對射式光電開關 > 氣泡液位傳感器

氣泡液位傳感器

型號:OPB350L125

產品時間:2021-09-26

產品資料:查看pdf文檔

簡要描述:

OPB350L125氣泡液位傳感器設計用于1/16英寸[1.6mm]1/8英寸[3.2mm]、3/16英寸[4.8mm]和1/4英寸[6.3mm]外徑的透明管。

詳細介紹

Description:

The OPB350 series liquid sensor is designed to work with 1/16" [1.6mm] 1/8" [3.2mm], 3/16" [4.8 mm] and 1/4" [6.3 mm] outside diameter clear tubes. When output reference circuitry is added, multiple output states such as “fluid present," “no fluid present" and “no tube present" can be recognized.

Clear liquid present causes the phototransistor to sink the maximum current, while dark liquid present causes it to sink the minimum current. As bubbles pass through the tube, the signal will vary between the “liquid present" and “no liquid" states. If no tube is present, the phototransistor sinks current between the dark fluid and clear fluid states. The customer will have to identify the typical current values for each situation. The ratio between the different states allows acknowledgement of different conditions.

The OPB350L series have leads that are designed to mount directly to PCBoards. The OPB350W series with 26 AWG wires are remote mountable. The OCB350 series provides a full solution with automatic calibration capability and a preset trip level.

The OCB350 series is configured to optimize the design effort needed to use a fluid sensor with the addition of self calibration circuitry. The OCB350 series are easy to use requiring only an optical device and power supply. Four lights are provided on the board that acknowledge when the device is calibrated (Green LED), that the device could not be calibrated (Red LED) and when the analog output has reached the logical trip higher than the calibration point (Blue LED) or lower than the calibration point (Green LED). The internal phototransistor load resistance can be set for three different values (~2.5K, ~9.6K or ~27K Ohms). A Reset/Clear pin is provided for remote signaling to calibrate of the system.

The OCB350 series comes with an OPB350L_ _ _Z, PCBoard, interface cable (OCB100-MC24) and all the necessary electronics required for sensing either transmissive or opaque fluids. See “Theory of Operation" for detailed information. For a custom PCBoard design for your unique challenge, contact your OPTEK representative.

Features:

• Can identify if liquid is present in clear tubes that have an outside diameter of 1/16" [1.6mm], 1/8" [3.2mm], 3/16" [4.8 mm] or 1/4" [6.3 mm]

• Opaque plastic housing enhances ambient light rejection

• Printed circuit board mounting or 24" (610 mm) 26 AWG wires

Applications:

• Non-contact fluid sensing

• IV fluid

• Oils and other petroleum products

• Colored fluids

• Toner fluids

• Water

OPB350L125氣泡液位傳感器說明:
OPB350系列液體傳感器設計用于1/16英寸[1.6mm]1/8英寸[3.2mm]、3/16英寸[4.8mm]和1/4英寸[6.3mm]外徑的透明管。當添加輸出參考電路時,可以識別多種輸出狀態,例如“有流體"、“無流體"和“無管存在"。
透明液體的存在使光電晶體管吸收最大電流,而深色液體的存在使光電晶體管吸收最小電流。當氣泡通過管道時,信號將在“有液體"和“無液體"狀態之間變化。如果沒有管存在,光電晶體管在暗流體和透明流體狀態之間吸收電流??蛻舯仨毚_定每種情況下的典型電流值。不同狀態之間的比率允許確認不同的條件。
OPB350L系列具有設計用于直接安裝到PCB板的引線。OPB350W系列具有26根AWG導線,可遠程安裝。OCB350系列提供具有自動校準功能和預設跳閘水平的完整解決方案。
OCB350系列配置為優化使用流體傳感器所需的設計工作,并添加自校準電路。OCB350系列易于使用,只需要光學設備和電源。電路板上提供了四個指示燈,用于確認設備何時校準(綠色LED)、設備何時無法校準(紅色LED)、模擬輸出何時達到高于校準點(藍色LED)或低于校準點(綠色LED)的邏輯跳閘。內部光電晶體管負載電阻可設置為三個不同的值(~2.5K、~9.6K或~27K歐姆)。復位/清除引腳用于遠程信號,以校準系統。
OCB350系列配有OPB350L___Z、PCB板、接口電纜(OCB100-MC24)以及傳感透射或不透明液體所需的所有必要電子設備。有關詳細信息,請參閱“操作理論"。
OPB350L125氣泡液位傳感器特征:
•能夠識別外徑為1/16英寸[1.6mm]、1/8英寸[3.2mm]、3/16英寸[4.8mm]或1/4英寸[6.3mm]的透明管中是否存在液體
•不透明塑料外殼增強了環境光抑制能力
•印刷電路板安裝或24英寸(610毫米)26 AWG電線
應用:
•非接觸式流體傳感
•靜脈輸液
•石油和其他石油產品
•有色液體
•碳粉液
•水

 


產品咨詢

留言框

  • 產品:

  • 您的單位:

  • 您的姓名:

  • 聯系電話:

  • 常用郵箱:

  • 省份:

  • 詳細地址:

  • 補充說明:

  • 驗證碼:

    請輸入計算結果(填寫阿拉伯數字),如:三加四=7

上一篇:OPB830 and OPB840 (L and W)

下一篇:OPB815WZ

版權所有 © 2019 上海蒸鑫電子科技有限公司 滬ICP備14039699號-1 技術支持:化工儀器網 管理登陸 GoogleSitemap

在線客服 聯系方式 二維碼

服務熱線

86-021-64576299

掃一掃,關注我們

日本三级欧美三级人妇视频